Awesome Nature-Landscape Photography – Getting the Correct Exposure is Essential

Awesome Nature-Landscape Photography – Getting the Correct Exposure is Essential

Getting the right exposure is essential to any quality nature photo.

Exposure is the amount of light that is let into the camera which contributes to the photograph that is recorded. A good exposure has the correct amount of light to produce a balanced shot.

Light is the key word here. Allowing the correct amount of light in can be tricky, but luckily our cameras have automatic features that measure it. Some cameras allow a manual feature which means we can manipulate the amount of light that reaches the camera. If we allow too much, the photograph becomes overexposed, meaning the image is too light and washed out. Details become hard to see in an overexposed picture.

To the same effect if we let too little light in, the photograph is underexposed. This means that the picture is darker than it should be. This makes the photograph look shadowy and gloomy, but underexposing is still better than overexposing. Why? Because the picture can be lightened later and the detail will still be there, whereas in an overexposed picture, details cannot be rescued as they were never captured in the first place.

Your camera will have a function to adjust the brightness. This is symbolized by the + or – symbol, normally allowing you to adjust the light by 3 stops either way. You need to do this before you take the image. So for example, you could take a photograph of a tree, and decide it is far too bright because of the sun. So you need to change the exposure to -1, then take the shot again and see if it has helped. If it is still too bright you could reduce it to -2 and see if the shot is satisfactory.

This is sometimes called bracketing. When you take the same shot but at different exposures from -2 to -1 to 1 to +1 to +2, this is bracketing. It gives you the option to choose the best photograph of the bunch.


Metering is the way that your camera decides on the correct exposure. The meter in your camera measures the amount of light in the area where you are taking the photograph. Ideally, the camera will pick up on a mid toned area that is neither too dark nor too light, so that the light is balanced. When you buy a SLR camera you will be given a few options on how to meter your images.

There is ‘centre weighted’ or ‘average metering’. This means that the camera will take an average of the light in the scene. Most cameras focus on the centre of the photograph, whereas some take into consideration the edges. Since the focus of a picture is generally in the centre of a frame, this produces a good overall result.

Multi Zone metering is also known as ‘Matrix metering’. This method calculates various zones in the scene to come up with the best exposure normally from several spots. Different branded cameras will differ in results.

Then there is ‘Spot metering’. With this method only a small area of the viewfinder is measured, typically a ‘spot’. For the best results, you should move the spot to a mid toned area so you get an even amount of light.

The advantage of spot metering is that it is very accurate and you can control it tightly. It is good for difficult scenarios, for example, when we have a bright beam of light, then very dark areas. Too greater contrast between dark and light confuses the camera. Average metering would presume that the whole scene was bright and meter incorrectly. With spot metering, we can choose a grey area so that the camera will not overestimate the light and compensate accordingly.

A good way to become familiar with spot metering is by choosing the function and pointing it at different areas of the same scene and taking the photographs. Then compare how choosing the different areas affects the finished picture.

Most professionals will choose spot metering for landscape photography as it gives greater control.

Where speed is important, Matrix metering is useful as there is less guess work involved.


Flash is commonly used with point and shoot cameras but is used with caution in landscape and wildlife photography.

Flash is normally attached to the camera body. When the camera detects low light, the flash pops up automatically, although you can manually adjust the settings so that it will remain down.

If you require more power, you can buy a separate flash head. This is common in press and fashion photography, where they spend a lot of time working at night or indoors and they need to be able to capture evenly lit images when there is plenty of action going on without any risk of blurring or poor lighting.

Flash is useful in a night time situation. If there is no other light source then you will have to use flash although you can use creative techniques like delayed flash to capture some movement and trails of light.

Overall though, the effect with flash can be harsh. It is also unsuitable for reflective surfaces like mirrors, as it will shine the bright light back into the camera. For landscape photography you need to know how to turn the flash off, especially if you are using a slow shutter speed for the specific blurring as the camera will automatically want to use flash.

Flash is useful in extremely dark situations as a fill-in light. This is called flash fill, and is used when you have a bright sun behind the subject and all that is left is the silhouette of the object. Using flash will put the detail back into the image.